Peugeot 208 Key Replacement

It is recommended to leave the replacement of Peugeot 208 keys to auto locksmiths equipped with the necessary equipment and technical knowledge. They can create and program new keys faster than a dealership would and at a cheaper cost.

If your key fob stopped locking or unlocking your doors it is likely due to a dead coin battery. There are also other reasons for the key to be malfunctioning.

Dead Coin Battery

A dead coin battery can hinder your Peugeot 208 from locking or unlocking, and cannot start the engine. If this is the case, you'll need to use the backup starting method that is detailed in the owner's manual to your vehicle.

Another reason your 208 might not start is that the spark plugs are worn down. The spark plugs ignite the fuel to start the engine. They are only able to last for a short time. If they are not used enough they will eventually fail.

There is an easy solution to this problem. Verify the voltage of your battery using a multimeter. If the voltage is below 11,5 volts, it's time to replace it. It is also necessary to clean the contacts of the battery when it has corrosion. This can be accomplished by taking off the rubber covers from the two terminals of the battery, and then using a wirebrush to eliminate any damaged parts of the battery. Then, you should connect your cables to connect the positive and negative poles.

Water Damage

If your 208 won't start and the battery has not been replaced, you must look at the spark plugs. You may find that they're dirty and don't spark. The spark plugs can be cleaned in a workshop.

Peugeot cars are equipped with a key with a transponder compatible with the immobiliser. This ensures that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it will not send the proper signal to the vehicle.

Water damage is a frequent cause of this problem. This is a typical issue in warmer climates where the vehicle is exposed to rain or snow. If this is the case, you should call a reputable auto locksmith who will have all the tools and equipment needed to modify the new key. They will also have the most up-to-date technology and equipment needed to make the Peugeot 208 smart key. The process shouldn't take longer than 15 minutes.

Faulty battery contacts

peugeot 5008 key (content) replaced the transponder chips with a brand new model that utilizes electronic components that are mounted on a circuit board. The new system is excellent when it's brand new, but the circuit boards degrade over time and cease to function properly.

This could stop the immobiliser from triggering so that the vehicle won't start. If this happens it's a good idea to seek out a Peugeot specialist or locksmith.

A common issue is when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into your lock. A car locksmith can replace the battery and cut a fresh blade for you, it's generally a quick fix.

Faulty Receiver Module

It could be that the receiver module is faulty if your Peugeot key fob stops working after being dropped on the floor, or exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to the onboard computer, which controls the central locking system of your peugeot 208 key fob not working vehicle.

The key fob itself has rubber seals to prevent water from reaching the electronic chip inside. However, prolonged exposure to water may be able to penetrate these seals and cause damage to the chip. The high salt content of the pool or ocean waters could cause damage to the key fob, especially if it is submerged.

If your Peugeot spare key fob stops working then you'll have to get the module replaced. This can only by done by a Peugeot specialist or a professional auto locksmith. Peugeot keys like other cars are protected by an immobilizer system. This requires the right code to begin the car. This is why you must be able to trust a professional Peugeot locksmith to handle the task of programming and creating the replacement.

Computers with faulty on-board computers

The on-board computer in your Peugeot is responsible for a number of the systems in the car, from power windows to the airbags. The on-board computer displays a code when something goes wrong. This code is stored inside the system and will stay there until the problem is solved. In most cases, this will require the on-board computer being replaced.

The most common cause of the warning light for the airbag to flash is corrosion or loose connections in the sensor. It can be due to wear and tear, aging, or exposure to salt and moisture. It is essential to have this issue resolved as soon as you can, as an airbag that is malfunctioning can be dangerous in the event an accident.

If your Peugeot is showing a card detected as not present error then the key battery inside the key fob may be dead or weak. This can prevent the key fob from transmitting a signal that will disable the standard immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If this does not work then the battery in the key fob is in need of replacement.