Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinctly SUV-like feel due to its larger dimensions. Moreover, the wheel sizes of 19 inches in Ti and ST-L models can be firm at times. The front tyres in the Qashqai could also lose grip on rough surfaces and its CVT can sometimes display wrist-flexing torque steering.

This is typically caused by dead batteries, which can be replaced in just a few minutes. Be sure that the replacement battery is of the same size, voltage and specifications.

Water Damage

Water damage is one of the most frequent causes for the nissan qashqai key replacement uk keyfob to display the "key ID is incorrect" message. The key fob comes with rubber seals that shield the electronic chip inside. However, prolonged exposure to moisture could cause it to cease functioning properly. It is common to observe this happen if your key fob was dropped in the ocean or swimming pool. It can also happen when it gets wet due to rain or soapy hand.

If your key fob has been exposed to water for many years it is possible to clean it with isopropyl or electronic cleaner. It could also require to be taken to a professional to be repaired or replaced.

If your key fob needs to be replaced, it is quite simple to do. Make sure you have the right multipack (CR2032, 3V). The front and rear cases with a flathead screwdriver. It is necessary to remove the clips for retaining metal and remove the old battery, then put in the new one. Reassemble the fob and replace the mechanical key. Verify that it is working correctly. If it isn't then you'll need to go to your local nissan qashqai keys Locked in Car dealer or an experienced auto locksmith to repair the chip on the key. The chip is usually not damaged by water and therefore shouldn't be too expensive.

Dead Coin Battery

The coin battery is a second common reason why your Nissan Qashqai remote key fob might not work. These batteries usually last 3-5 years, but they can become depleted over time, especially if the fob is frequently dropped. You can replace the battery but ensure it's the same voltage and same size as the first. If you replace the battery, it could cause the key to be assigned an incorrect key ID. This can prevent it from being connected to your vehicle.

The best way to replace the battery in the Nissan Qashqai key fob is by removing the fob with the small screwdriver with a flat-head. The screwdriver needs to be inserted into a small hole on the bottom of your key fob. Simply twist the screwdriver to divide the two halves. Remove the old CR2025 battery and replace it with a brand new one, taking note of the location of the old one in the fob.

Before putting the new battery in place check to ensure there isn't any dirt or water damage on the terminals. If not clean the terminals with small amounts of isopropyl alcohol. Make sure that the pole cables are properly connected. They should be connected to the positive and negative poles of your battery.

Diagnostics of a fault

If your Nissan Qashqai key fob stops working after exposure to clean tap water or rain it could be an indication of a chip issue inside. You'll require a new keyfob if you are unable to fix the issue by replacing the battery. If the key fob didn't work after you dropped it, it's likely that the chip inside was damaged. You can usually get the key fob back to function once more if you remove and clean the chip using paper towel and isopropyl alcohol and then put it back in.

Key ID Incorrect is a common error that you can see on the dashboard of your car. This means that the car is unable to recognize the key fob, and will not allow it to start the engine. The problem can be caused by a variety of things, including water damage, undetectable problems in the key fob's circuitry or RFID interference.

If the battery that powers 12 volts in your key fob is broken or is not supplying enough electrical current, it will stop working. This could affect the remote keyless system as well as central locking on your Nissan Qashqai, as well as hindering you from starting your engine with the key fob (if equipped with Intelligent Key). Check the battery in the key fob if you're not able to lock or unlock your door by hand. You could also try replacing the battery to reset your transmitter.

Reprogramming

Unless the key fob has been submerged in salt water the device should be able to come back to life after a quick wash with clean water. You might also try cleaning your electronic chip with isopropyl alcohol or an electronic cleaner. If none of the above works it is possible to replace the key fob.

If your Nissan Intelligent Key still does not work, there could be a connection issue between it and your vehicle. To relink it, start by turning the key into the ignition, without turning on the car. Continue to do this until you see the warning lights flash twice. Turn off the vehicle and take off the key.

Next, you must open the fob compartment inside your vehicle. It is usually located on the door jamb or the handle for the driver's door. Find the small "program" button and press it. You should hear a chime sound after the process has been completed.

Now that your Intelligent Key is relinked to the car, it's time to test it out. Make sure you press all the buttons on the key while at a distance from the vehicle. If the lights flash and the horn squeaks it means that the key has successfully linked to the Nissan. You can also test it close to the Nissan.